75038.54USD
55.25USD
1.41USD
0.1USD
2363.4USD
8.52USD
625.26USD
85.4USD
0.04USD
0.03USD
0.05USD
Video Upload Q&A Likes Trends
@Ada
S9K does not support board stacking. If the control board is not faulty, please export the complete kernel log and analyze it for further investigation.
What could be the reason for the S9K's chip model replacement resulting in a computational power of only 3.6T during machine testing?
@Ada
1\ Test the diode value and voltage of the 3 transistors Q5,Q14,and Q15 comparing the working hashboard. 2\ Test the DC-DC circuit.Remove all components related to short circuits on the board. 3\ Connect Q5 Pin-G to D3 and inspect the boost section for any issues.
What could be the issue if Q5 on the S9K, when removed and tested, shows a reading of 0.8, while Q8 on the faulty board has an abnormal input?
@Ada
1. Tighten the screws on the power supply copper busbar. 2. Replace the copper busbar with a new one. 3. Replace the screws. 4. Upgrade to the latest firmware.
What could be the problem if the Antminer S11, with a functioning board, consistently displays low voltage and subsequently shuts down?
@Ada
IP address conflict. Connect the miner's network cable to the laptop and check if you can obtain an IP address and access the internet. Then,reconfigure the static IP address.
What could be the issue if the machine's Light is green, but it cannot be detected through its IP address, and accessing the backend is also not possible?
@Ada
Check the miner status,there different frequency and no fan speed. 1st,eliminate the power supply as a possible cause. 2nd,try reprogramming the PIC of the hashboard with a frequency of 500. After reprogramming, the frequency should be 550. 3rd,do single-board test for the hashboard with 0 hashrate.
When the machine is running, does it consistently restart despite attempts to flash the firmware?
@Ada
First check the fans. The fan error rate has increased, leading to a decrease in hashrate, and ultimately resulting in a network failure. If changing the fan can't solve the problem, check the network again. If it still doesn't work, the CPU of the control board may be faulty.
According to the provided image, why does the machine disappear from scanning after running for two days?
@Ada
If the PSU and mosfet are OK,it may be caused by 1\ The voltage configuration in the CONFIG file has been set the too high. 2\ The abnormal voltage domains or ground issues 3\ The abnormal signals Is there full asic? Replace the U22 and the capacitors,resistors,mosfets around it.It is possible that they were not completely replaced, resulting in a failure when powering up.
What could be the issue if the S9K DC-DC output for headphones is too high at 10.8V, while it should be normal at 10.2V?
@Ada
Check whether there is full chips from kernel log. If missing chips,do single-board test. If the chip's hashrate is low, replace it. Check the 3 hashboards temp sensor model,keep them the same.
On the S9i machine test, is there a significant number of chips but insufficient hashrate?
@Ada
Check whether there is full chips from kernel log. If missing chips,do single-board test. If the chip's hashrate is low, replace it. Check the 3 hashboards temp sensor model,keep them the same.
On the S9i machine test, is there a significant number of chips but insufficient hashrate?
@Ada
First review the kernel log and then find out the error, solve it.
Where should I check for the logs of the S17Pro?
@Ada
To check the kernel log and do single-board test to find out the error and then solve it.
Is there a lack of hashrate when running the entire system，How to solve the issue？
@Ada
Keep power on the hashboard,test the voltage of RI,BO,RST,CO,CLK to find out the abnormal chip and repalce it. Or the temp sensor error. Configrate the right temp sensor file.
The test shows garbled characters, how to solve it?
PgUp...2728293031PgDn
Recommend
@mgmmgm61
Enthusiast
@70b14fde6c
Other Roles
@obasosaro18
Other Roles
@mansouri2244
Individual Miner
@uri
Other Roles
@9c0f0b7c8a
Other Roles
Hot Topics
Lucky Miner LV07 Firmware
7204
See the below single-board test result. There are 8.4V,8.5V domain voltage, replacing chip 1 did not work.
6874
As shown in the picture below, T15 machine, 58, 59, 60 are all replaced, it still doesn’t work, what’s the problem.
6838
How To Install Bitmain S19 And S19j Pro Low Power Mode Firmware: Step-By-Step
6232
Lucky Miner Wi-Fi reconnect
5738
LTC Mining with Lucky Miner Lv06
5581
Back to firmware Lucky Miner Lvl 06: I need the www.bin file. Can someone help?
5234
Lucky miner v6
5128
Cannot access IP address lucky miner
5112
Lucky miner LV06 breakdown
4866
Hot download
Luckyminer LV06-V2.3.0_upgrade firmware 页面升级固件
1435
Luckyminer LV06 factory firmware V2.1.0 页面升级固件
617
Luckyminer Management Tool
589
Solo Miner_Lucky Miner User Guide LV05-LV08_20231215
411
Luckyminer LV07 Instruction and User Guide PC English
177
Luckyminer LV 07 Product Manual
141
Luckyminer LV06 ESP-Prog JTAG Debug Guide_Tool kit
139
SOLO Miner_Nerdminer USB Shape（V3）配置说明1107
137
IceRiver_MinerTool_English_V1.0.15 (1)
127
Luckyminer乐透机用户使用说明LV05-LV08(2023.12.15)
87

No. 199, Zhaojuesi South Rd, Chenghua District, Chengdu, Sichuan, China

No.14, Jian'an Rd, Bao An District, ShenZhen, GuangDong, China

+86 15390421113

minerfixesofficial@gmail.com

About Us Contact Us FAQ News
Bitaxe Project Bitaxe Github OSMU Official OSMU Discord Bitaxe Web Flasher
Privacy Policy Terms & Conditions
2022 Minerfixes - All Rights Reserved